Crown XTi 1002 Pro 1000W Power Amplifier

XTi
There's no debate – when you choose Crown's XTi 2 Series, you're choosing one of the most powerful and innovative amplifiers on the market today. That's because the all-new XTi 2 Series amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.

Next Generation Features:

• Peak_x Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
• Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
• 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
• New system monitoring provides software visibility of AC line voltage and power supply temperature
• Integrated cast-aluminum handles for easy handling and enhanced durability
• Locking power cord clip provides a secure connection between the amplifier and power cord
• Updated HiQnet System Architect™ control software
• Increased number of presets to a total of 50; 49 of which are user definable

Integrated Processing

Input EQ	6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
Crossover Filters	Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.
Output EQ	8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
Delay	For signal alignment of driver; 50 mS of total delay.
SubHarmonic Synth	Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
Peakx™ Plus Limiter	User defeatable limiter that allows users to control Threshold, Attack, and Release times.
Presets	50 total presets, 49 of which are user-definable.

Performance

Sensitivity (for full rated power at 4 ohms)	1.4 Vrms
Frequency Response (at 1 watt, 20 Hz - 20 kHz)	+0 dB, –1 dB
Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms)	XTi1002/2002/4002: 100 dB (A weighted) XTi6002: 103 dB (A weighted)
Total Harmonic Distortion (THD)	< 0.5%
Damping Factor 20 Hz to 1 kHz	> 500
Crosstalk (below rated power)	20 kHz - 1 kHz: > 70 db
Input Impedance (nominal)	20k ohms balanced, 10k ohms unbalanced
Maximum Input Signal	+22 dBu typical
AC Line Voltage and Frequency Configurations	100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)	XTi1002: 6.8A; no more than 38W at idle XTi2002: 8.3A; no more than 38W at idle XTi4002: 10.5A; no more than 38W at idle XTi6002: 15.3A; no more than 180W at idle
Operating Temperature	0°C to 40°C at 95% relative humidity (non-condensing)

Controls

Level	Two front-panel rotary level controls, one for each channel
Power Switch	On/Off switch applies AC power to the amplifier
Sel/Prev/Next Buttons	Three buttons near the LCD screen that are used to access menu items and front panel lockout
LCD Screen	Backlit liquid crystal display that shows preset and processing status

Indicators

Signal Indicator	Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
–10 Indicator	Green LED flashes when output signal exceeds -10 dB below clip.
–20 Indicator	Green LED flashes when output signal level exceeds -20 dB below clip.
Ready Indicator	Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator	Red LED, one per channel, turns on at the threshold of audible distortion
Temp Indicator	Red LED, one per channel, illuminates under excessive temperature conditions
Power Indicator	Blue LED illuminates when the amplifier has been turned on and has power

Input/Output Connectors

Input Connectors	XLR, one per channel
Link/Out Connector	Loop-thru signal from input connector for linking another amplifier, one per channel.
Output Connectors	Two Neutrik® Speakon®NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
HiQnet™ USB Connector	Type B, connects to HiQnet™ network.

Construction