Crown XTi 4002 Pro 2400W Power Amplifier   Crown XTi 4002 Pro 2400W Power Amplifier

Crown XTi 4002 Pro 2400W Power Amplifier
Item Code
Extended Warranty
  • Overview
  • Feedback
  XTi 1002 XTi 2002 XTi 4002
2Ω Stereo (per ch.) 700W 1000W 1600W
4Ω Stereo (per ch.) 500W 800W 1200W
8Ω Stereo (per ch.) 275W 475W 650W
8Ω Bridge-Mono 1000W 1600W 2400W
4Ω Bridge-Mono 1400W 2000W 3200W

There's no debate – when you choose Crown's XTi 2 Series, you're choosing one of the most powerful and innovative amplifiers on the market today. That's because the all-new XTi 2 Series amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.

Next Generation Features:

  • Peakx Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
  • Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
  • 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
  • New system monitoring provides software visibility of AC line voltage and power supply temperature
  • Integrated cast-aluminum handles for easy handling and enhanced durability
  • Locking power cord clip provides a secure connection between the amplifier and power cord
  • Updated HiQnet System Architect™ control software
  • Increased number of presets to a total of 50; 49 of which are user definable

Integrated Processing

Input EQ

6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.

Crossover Filters

Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.

Output EQ

8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.


For signal alignment of driver; 50 mS of total delay.

SubHarmonic Synth

Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.

Peakx™ Plus Limiter

User defeatable limiter that allows users to control Threshold, Attack, and Release times.


50 total presets, 49 of which are user-definable.


Sensitivity (for full rated power at 4 ohms)

1.4 Vrms

Frequency Response (at 1 watt, 20 Hz - 20 kHz)

+0 dB, –1 dB

Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms)

XTi1002/2002/4002: 100 dB (A weighted)
XTi6002: 103 dB (A weighted)

Total Harmonic Distortion (THD)

< 0.5%

Damping Factor 20 Hz to 1 kHz

> 500

Crosstalk (below rated power)

20 kHz - 1 kHz: > 70 db

Input Impedance (nominal)

20k ohms balanced, 10k ohms unbalanced

Maximum Input Signal

+22 dBu typical

AC Line Voltage and Frequency Configurations

100 VAC, 120 VAC, 220-240 VAC 50/60 Hz

AC Line Current
(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)

XTi1002: 6.8A; no more than 38W at idle
XTi2002: 8.3A; no more than 38W at idle
XTi4002: 10.5A; no more than 38W at idle
XTi6002: 15.3A; no more than 180W at idle

Operating Temperature

0°C to 40°C at 95% relative humidity (non-condensing)



Two front-panel rotary level controls, one for each channel

Power Switch

On/Off switch applies AC power to the amplifier

Sel/Prev/Next Buttons

Three buttons near the LCD screen that are used to access menu items and front panel lockout

LCD Screen

Backlit liquid crystal display that shows preset and processing status


Signal Indicator

Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).

–10 Indicator

Green LED flashes when output signal exceeds -10 dB below clip.

–20 Indicator

Green LED flashes when output signal level exceeds -20 dB below clip.

Ready Indicator

Green LED, one per channel, illuminates when the amplifier is ready to produce audio.

Clip Indicator

Red LED, one per channel, turns on at the threshold of audible distortion

Temp Indicator

Red LED, one per channel, illuminates under excessive temperature conditions

Power Indicator

Blue LED illuminates when the amplifier has been turned on and has power

Input/Output Connectors

Input Connectors

XLR, one per channel

Link/Out Connector

Loop-thru signal from input connector for linking another amplifier, one per channel.

Output Connectors

Two Neutrik® Speakon®NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).

HiQnet™ USB Connector

Type B, connects to HiQnet™ network.




Front Panel



Proportional speed fan with front-to-rear airflow.


XTi 1002/2002/4002: 19" (W) x 3.5" (H) x 12.25" (D)

Net Weight

XTi 1002/2002/4002: 18.5 lbs (8.4kg)

Shipping Weight

XTi 1002/2002/4002: 21.5 lbs (9.8kg)

Would you like to help others by submitting a review? Create an account and earn points for your reviews!

We carry your favorite brands

Enter-Tech Magic Mic
Singing Machine